Front Fender Inner, LH – for Ford Bronco 1966–77 (Steel)

Save your restoration hours for the work that shows: this replica front fender inner suits 1966–1977 Ford Bronco (First Generation) builds, left-hand (LH) side and replaces panels that would cost more in repair labour than they are worth. Manufactured in steel to match the original pressing, it fits the way the panel it replaces once did — without the rust, dents or filler.

Specifications

Fitment & Compatibility

This wheel housing fits the Ford Bronco (First Generation), model years 1966–1977. Panels listed for 1966–1977 fit all first-generation Broncos unless noted; 1966–1968 trucks differ in some trim and grille details, and 'uncut' rear quarters restore the factory wheel-arch line on trucks whose arches were cut. Test-fit before paint, as with any reproduction panel.

As with any reproduction panel, trial-fit against the vehicle before final welding or paint. Minor adjustment at flanges and mounting points is a normal part of professional panel fitting, even with precision replica pressings.

The maths of new steel

Restorers rarely regret buying a new panel; they regret the three weekends spent trying to save an old one first. Repairing a corroded wheel housing means paying for blasting, fabrication time and filler — and the result is still fifty-year-old metal. A replica pressing costs a known amount, arrives straight, and spares a donor vehicle from being cut up for parts. Your original panel can stay with the vehicle for provenance; your build gets metal you can trust.

About the Ford Bronco (First Generation)

The first-generation Ford Bronco, built from 1966 to 1977, has gone from farm truck to blue-chip collectible — early uncut Broncos now trade at prices that justify full body-off restorations. Ford built the early Bronco with a fully boxed frame and a simple welded steel body offered as a wagon, half-cab pickup and (briefly) roadster. Because so many Broncos had their rear quarters cut for larger tyres in the 1970s and 80s, straight original sheet metal is scarce, and complete reproduction bodies, cabs and individual stamped panels are now central to the Bronco restoration industry.

Early Broncos rust in the usual Ford truck places: floor pans front and rear, rocker panels, inner and outer rear quarters, wheel housings, fender aprons, door bottoms and the tailgate. The good news is that virtually every panel on a 1966–1977 Bronco is reproduced to a high standard, so builders can replace entire corroded assemblies — or start from a complete new body — rather than repairing pitted original steel.

Installation

Difficulty: Advanced  |  Typical time: 4–8 hours per side  |  Welding required: yes.

Wheel housings are welded structure. Drill the factory spot welds, remove the old housing, and trial-fit the new panel with clamps and self-tapping screws before committing to weld. Plug-weld at the original spot-weld locations, then seal every seam — the housing lives in constant spray and mud. Undercoat after paint.

Tools: spot-weld drill, MIG welder, clamps, seam sealer, weld-through primer.
Common mistakes to avoid: cutting out the old panel before the new one arrives, welding without weld-through primer on mating flanges, and leaving seams unsealed.

If you are not an experienced welder, we recommend professional installation for this panel — it is structural, and correct seam welding matters for both safety and finish.

Quality & Manufacturing

BodyBros replica panels are pressed on dedicated tooling developed from measured original panels, in automotive-grade material matched to the application. Pressings are checked against reference bucks for profile, flange geometry and hole placement before packing. Steel panels are supplied with a protective primer coating ready for preparation and refinishing; alloy and plastic parts are supplied ready to prepare and paint. These are aftermarket replica restoration parts — manufactured by BodyBros, not by the original vehicle maker.

Worldwide Delivery

We ship worldwide — including the United States, Canada, the UK, Europe, Australia and New Zealand. Panels are packed in purpose-built cartons or timber crates depending on size; large assemblies travel by sea or air freight with tracking. Duties and taxes are calculated at checkout or on arrival depending on destination. See our Shipping & Delivery page for lead times to your region.

Frequently Asked Questions

Will this wheel housing fit my Ford Bronco (First Generation)?

It fits 1966–1977 models as listed above. Panels listed for 1966–1977 fit all first-generation Broncos unless noted; 1966–1968 trucks differ in some trim and grille details, and 'uncut' rear quarters restore the factory wheel-arch line on trucks whose arches were cut. Test-fit before paint, as with any reproduction panel.

Is welding required to install it?

Yes — this is a welded structural panel. It should be trial-fitted, clamped and plug-welded at the factory seam locations, ideally by an experienced welder.

Can it replace a rusted original panel?

Yes — that is exactly what it is made for. The Ford Bronco (First Generation) commonly rusts in floor pans, rockers, rear quarters and wheel housings, fender aprons, door bottoms and tailgates, and this replica pressing replaces corroded original metal with new steel — no donor vehicle required.

Do you ship this internationally?

Yes. We ship worldwide with tracked freight; larger panels and assemblies travel in purpose-built crates. Delivery times and freight options for your country are shown at checkout and on our Shipping page.

What finish does the panel arrive in?

It arrives ready for preparation and paint. Like any replacement body panel, it should be test-fitted, prepared and refinished before final installation.

BodyBros is an independent manufacturer of replica restoration panels. Vehicle make and model names are used for fitment identification only; BodyBros products are aftermarket parts and BodyBros is not affiliated with or endorsed by Ford.

Explore more: all Ford Bronco (First Generation) panels · inner guards & wheel housings · how to choose reproduction panels